Tài liệu Bai do nghiem thu ip dslam hw ma5600

TẬP ĐOÀN BƯU CHÍNH VIỄN THÔNG VIỆT NAM CỘNG HOÀ XÃ HỘI CHỦ NGHĨA VIỆT NAM Độc lập - Tự do - Hạnh phúc BAN QUẢN LÝ DỰ ÁN CÁC CÔNG TRÌNH VIỄN THÔNG Số: 42 /VNPT-CTVT Hà Nội, ngày 16 tháng 01 năm 2014 V/v Bài đo nghiệm thu thiết bị IP DSLAM MA5600 của Huawei trang bị đợt I năm 2014 Kính gửi: - Viễn thông các tỉnh, thành phố: Phú Thọ, Hà Tĩnh, Bình Định, Lào Cai, Tuyên Quang, Đắc Nông, Hà Giang, Đắc Lắk, Thái Nguyên, Quảng Nam, Bắc Kạn, Gia Lai, Thanh Hóa, Thái Bình, Khánh Hòa, Quảng Ninh, Kon Tum, Nam Định, Lạng Sơn, Ninh Thuận, Ninh Bình; - Công ty VNPT Technology. Tiếp theo Công văn số 08/VNPT-CTVT, ngày 03/01/2013, của Ban QLDA các CTVT V/v cung cấp thông tin dự án “Trang bị bổ sung thiết bị xDSL cho một số Viễn thông tỉnh, thành phố phục vụ phát triển thuê bao đợt I năm 2014”. Lần này Ban xin gửi tới các Đơn vị Bài đo nghiệm thu hệ thống thiết bị IP DSLAM MA5600 của Huawei đã được Tập đoàn phê duyệt. Tập đoàn yêu cầu các Viễn thông tỉnh, thành phố được trang bị thiết bị IP DSLAM MA5600 của Huawei đợt I năm 2014 sử dụng Bài đo này để tiến hành đo kiểm nghiệm thu hệ thống thiết bị. Trong quá trình thực hiện, nếu có vấn đề vướng mắc xin liên hệ: Đầu mối liên hệ phía Ban QLDA: - Ông Nguyễn Khắc Hoan – Phó phòng KT Điện thoại: 094 720011, CQ: (04) 37741465; Emai: [email protected] Đầu mối liên hệ phía nhà thầu VNPT Technology: - Ông Phùng Thế Khiêm Điện thoại: 0903 222235; Email: [email protected] Xin trân trọng cám ơn sự phối hợp của các Đơn vị./. KT. GIÁM ĐỐC PHÓ GIÁM ĐỐC Nơi nhận: - Như trên; - Giám đốc Ban (để b/c); - Lưu: VT, NKH(01). (Đã ký) Tài liệu đính kèm: Bai Do Nghiem Thu IP DSLAM HW MA5600-2014 AIS: 8231 - VBĐT Lê Như Anh 1 PROCEDURE OF TEST IP DSLAM VNPT 2014 No. Equipment Name 1 ADEE Board 2 ADEE Board 3 ADEE Board 4 ADEE Board 5 ADEE Board .. … .. … .. … .. … .. … Serial Number Test Result (Passed/Failed) Remark Procedure of Test IP DSLAM LISTS OF TEST ITEMS Item Inde x Item name Sub Item index Sub Item name Test Result 1 0101 ADSL G.dmt □Passed □Failed □Not Test 2 0102 ADSL T1.413 □Passed □Failed □Not Test 0103 ADSL/ADSL2+ full compatibility □Passed □Failed □Not Test 4 0104 CPE intercompatibility test □Passed □Failed □Not Test 5 0105 xDSL active port rate □Passed □Failed □Not Test 3 T01-01 xDSL test items 6 T01-02 Mutual Influence Test 0201 Mutual Influence Between Data Service and Voices Service □Passed □Failed □Not Test 7 T01-03 Triple-play services 0301 Multi-service testing (Internet, VPN, IPTV) □Passed □Failed □Not Test T01-04 ADSL2+ Board functions test items 0401 ADSL channel mode (Fast/Interleave) □Passed □Failed □Not Test 0402 Noise threshold setting □Passed □Failed □Not Test 0501 Querying the details of the ADSL port □Passed □Failed □Not Test 0502 Configuring an ADSL2+ Line profile □Passed □Failed □Not Test 0503 ADSL2+ IPoE/PPPoE access service □Passed □Failed □Not Test 13 0504 Triple-play service □Passed □Failed □Not Test 14 0601 Line Evaluation for Single/Multiple lines □Passed □Failed □Not Test 15 0602 SELT test for Single/Multiple lines □Passed □Failed □Not Test 0603 DELT test for Single/Multiple lines □Passed □Failed □Not Test 17 0604 Line Length for lines □Passed □Failed □Not Test 18 0605 Rate Fulfilled for lines □Passed □Failed □Not Test 8 9 10 11 12 16 T01-05 N2000 compatiblity test T01-06 N2510 compatiblity test Remarks: T0106: remote user login to VNPT N2510 for testing Representative of VNPT: Date: Trang bị bổ sung thiết bị cho các hệ thống IP DSLAM Huawei đợt I năm 2014 Page 1 of 21 Procedure of Test IP DSLAM T01-01 xDSL Service test T01-0101 G.dmt Objective To test how the ADSL2+ board supports G.dmt Network diagram PC Server Internet PC Prerequisites Procedure Expected result z z 1. 2. CPE MA5600 BRAS The CPE supports G.992.1, G.992.3, and G.992.5. The cabling for the CPE is correct. Run the command interface adsl to enter ADSL2+ configuration mode. Run the command adsl line-profile add to add an ADSL2+ line profile with the ADSL working mode of G.dmt. 3. Run the command activate to activate the port of the CPE connected with the MA5600 by using the profile added in step 2. 4. Set the working mode of the CPE to G.dmt and connect it with the MA5600 to activate the ADSL2+ port. 5. Run the command display line operation to view the activation mode of the ADSL2+ port. 6. Test the service connectivity between the PC and the server. 1. The ADSL2+ port can be activated in G.992.1 mode, G.992.3 mode, or G.992.5 mode. 2. The service between the PC and the server is normal. Remarks Test Result Passed [ ] Failed [ ] Not tested [ ] Date/Time: Signature Representative of VNPT: …………………………………………………………………………….. Trang bị bổ sung thiết bị cho các hệ thống IP DSLAM Huawei đợt I năm 2014 Page 2 of 21 Procedure of Test IP DSLAM T01-0102 T1.413 Objective To test how the ADSL2+ board supports T1.413 Network diagram PC Server Internet PC Prerequisites Procedure Expected result z CPE MA5600 BRAS The CPE supports T1.413 mode. z The cabling for the CPE is correct. 1. Run the command interface adsl to enter ADSL2+ configuration mode. 2. Run the command adsl line-profile add to add an ADSL2+ line profile with the working mode of T1.413. 3. Run the command activate to activate the port of the CPE connected with the MA5600 by using the profile added in step 2. 4. Set the working mode of the CPE to T1.413 and connect it with the MA5600 to activate the ADSL2+ port. 5. Run the command display line operation to view the activation mode of the ADSL2+ port. 6. Test the service connectivity between the PC and the server. 1. 2. The ADSL2+ port can be activated in T1.413 mode. The service between the PC and the server is normal. Remarks The ADSL2+ port of an ADSL over ISDN board does not support T1.413. Test Result Passed [ ] Failed [ ] Not tested [ ] Date/Time: Signature Representative of VNPT: …………………………………………………………………………….. Trang bị bổ sung thiết bị cho các hệ thống IP DSLAM Huawei đợt I năm 2014 Page 3 of 21 Procedure of Test IP DSLAM T01-0103 ADSL/ADSL2+ full compatibility Objective To test how the ADSL2+ board supports ADSL2+ series recommendations Network diagram PC Server Internet PC Prerequisites Procedure Expected result z z 1. 2. CPE MA5600 BRAS The CPE supports G.992.1, G.992.2, G.992.3, G.992.4, G.992.5, and T1.413. The cabling for the CPE is correct. Run the command interface adsl to enter ADSL2+ configuration mode. Run the command adsl line-profile add to add a full-compatible ADSL2+ line profile. 3. Run the command activate to activate the port of the CPE connected with the MA5600 by using the profile added in step 2. 4. Set the working mode of the CPE and connect it with the MA5600 to activate the ADSL2+ port. 5. Run the command display line operation to view the activation mode of the ADSL2+ port. 6. Test the service connectivity between the PC and the server. 1. The ADSL2+ port can be activated in G.992.1, G.992.3, G.992.5, and T1.413 modes. 2. The service between the PC and the server is normal. Remarks Test Result Passed [ ] Failed [ ] Not tested [ ] Date/Time: Signature Representative of VNPT: …………………………………………………………………………….. Trang bị bổ sung thiết bị cho các hệ thống IP DSLAM Huawei đợt I năm 2014 Page 4 of 21 Procedure of Test IP DSLAM T01-0104 CPE compatibility Objective To test the compatibility of the ADSL2+ board with various ADSL2+ CPEs Network diagram PC Server Internet PC CPE MA5600 BRAS Prerequisites The cabling for the CPE is correct. Procedure 1. Set the activation mode of the ADSL user port in the MA5600 to fullcompatible mode. 2. Use ADSL2+ CPEs from different vendors to connect with the MA5600. No. CPE Type Vendor 1 2 3 Expected result 3. Use the default ADSL2+ line profile to activate the CPEs. 4. Test the service connectivity between the PC and the server. 1. 2. In step 3, each CPE is activated in an optimal mode (G.992.5 for the best). 3. After the CPE is activated, run the command display line operation to view the activation rate of the CPE in ADSL2+ mode, and you can find that the activation rate reaches the one configured in the line profile. In step 4, the service between the PC and the server is normal. Remarks Test Result Passed [ ] Failed [ ] Not tested [ ] Date/Time: Signature Representative of VNPT: …………………………………………………………………………….. Trang bị bổ sung thiết bị cho các hệ thống IP DSLAM Huawei đợt I năm 2014 Page 5 of 21 Procedure of Test IP DSLAM T01-0105 xDSL Activation rate port Objective To test the function of setting the activation rate of an ADSL2+ port Network diagram Server Internet PC Prerequisites z z z Procedure CPE MA5600 The MA5600 system runs normally. An RTU is connected to an ADSL2+ port, and the RTU works normally. You have logged in to the system as an administrator. 1. Run the command adsl line-profile modify to modify the activation rate of a port. For example, set the maximum downstream rate to 24 Mbit/s and the minimum one to 32 Kbit/s; the maximum upstream rate to 1 Mbit/s and the minimum one to 32 kbit/s. 2. Run the command activate to activate the port of the CPE connected with the MA5600 by using the profile modified in step 1. 3. After the CPE is activated, run the command display line operation to view the port activation rate of the CPE in board configuration mode. 4. Check actually down load data rate Line Profile Rate (kbps) Expected result Actual Data Rate (kbps) In step 3, the port activation rate of the CPE ranges between the minimum rate and maximum rate configured in the line profile. Remarks Test Result Passed [ ] Failed [ ] Not tested [ ] Date/Time: Signature Representative of VNPT: …………………………………………………………………………….. Trang bị bổ sung thiết bị cho các hệ thống IP DSLAM Huawei đợt I năm 2014 Page 6 of 21 Procedure of Test IP DSLAM T01-02 Mutual Influence test T01-0201 Mutual Influence Between Data Service and Voices Service Objective To test realtime alarm Network diagram None Prerequisites z z z Procedure The MA5600 system runs normally. The subscriber A and subscriber B work normal. Subscriber A and B is local users.. 1. Use telephone 1 and telephone 2 to dial each other for testing the communication quality. 2. Use telephone 1 and telephone 2 to dial each other for testing the communication quality when there are Data services over the cable. Expected result 1. Passes the SPL, the voices communication quality should not be affected. 2. The data services should not affect voice services, and the voice services should not affect data services Remarks None Test Result Passed [ ] Failed [ ] Not tested [ ] Date/Time: Signature Representative of VNPT: …………………………………………………………………………….. Trang bị bổ sung thiết bị cho các hệ thống IP DSLAM Huawei đợt I năm 2014 Page 7 of 21 Procedure of Test IP DSLAM T01-03 Multi-service testing (Internet, VPN, IPTV) Test item No: Date/time: Place: VNPT rep: Vendor rep: Test item : Service Test subitem: Internet, VPN, IPTV service Purpose: To verify the function of Internet,VPN, IPTV service Precondition: Preset conditions: Test procedure: 1. Create adsl line-profile (config)#adsl line-profile add 2 Start adding profile Press 'Q' to quit the current configuration and new configuration will be neglected > Do you want to name the profile (y/n) [n]:y > Please input profile name: DSLAM_Template > Please choose default value type 0-adsl 1-adsl2+ (0~1) [0]:1 > Will you set basic configuration for modem? (y/n)[n]: > Please select channel mode 0-interleaved 1-fast (0~1) [0]:0 > Will you set interleaved delay? (y/n)[n]:n > Please select form of transmit rate adaptation in downstream: > 0-fixed 1-adaptAtStartup 2-adaptAtRuntime (0~2) [1]:1 > Will you set SNR margin for modem? (y/n)[n]: > Will you set parameters for rate? (y/n)[n]:y > Minimum transmit rate in downstream (32~32000 Kbps) [32]: > Maximum transmit rate in downstream (32~32000 Kbps) [24544]:12000 > Minimum transmit rate in upstream (32~6000 Kbps) [32]: > Maximum transmit rate in upstream (32~6000 Kbps) [1024]:1024 Add profile 2 successfully 2. Deactivate old line-profile and activate new one. (config)#interface adsl 0/3 (config-if-adsl-0/3)#deactivate 0 Trang bị bổ sung thiết bị cho các hệ thống IP DSLAM Huawei đợt I năm 2014 Page 8 of 21 Procedure of Test IP DSLAM (config-if-adsl-0/3)#activate 0 profile-index 2 Send the command to activate port 0 successfully 3. Create traffic table IP index + HSI: (config)# traffic table ip index 11 name HSI_basic cir 512 4060 priority 0 priority-policy local-Setting + VPN: (config)# traffic table ip index 12 name VPN cir 512 512 priority 1 priority-policy local-Setting + IPTV: (config)# traffic table ip index 13 name IPTV cir 6000 7000 priority 4 priority-policy local-Setting 4. Create service VLANs (config)#vlan 100 smart (config)#vlan 1300 smart (config)#vlan 2400 smart (config)#vlan 99 smart (config)#port vlan 100 0/0 0 (config)#port vlan 1300 0/0 0 (config)#port vlan 2400 0/0 0 (config)#port vlan 99 0/0 0 // VLAN HSI // VLAN VPN // VLAN VoD // VLAN Muticast // port 0/0 0 is uplink 5. Create virtual channel (service-port): add subcriber + PVC for HSI : (config)#service-port vlan 100 port 0/3/0 vpi 8 vci 35 rx-cttr 11 tx-cttr 11 + PVC for VPN : (config)#service-port vlan 1300 port 0/3/0 vpi 1 vci 35 rx-cttr 12 tx-cttr 12 + PVC for VoD : (config)#service-port 242 vlan 2400 port 0/3/0 vpi 4 vci 35 rx-cttr 13 tx-cttr 13 6. Multicast configuration: (config)#multicast-vlan 99 (config-mvlan99)# igmp mode proxy (config-mvlan99)# igmp version v2 (config-mvlan99)# igmp uplink-port 0/0/0 (config-mvlan99)# igmp program add batch ip 232.84.1.1 to-ip 232.84.1.150 (config-mvlan99)#btv (config-btv)#igmp user add service-port 242 no-auth (config-btv)#multicast-vlan 99 (config-mvlan99)#igmp multicast-vlan member service-port 242 Expected Result: Customer can use internet, VPN, IPTV at the same time. • • • • VNP Service: PC1 can ping PC2 successfully. Download/upload rate between TFTP server and TFTP client achieve 80% of Configured Rate. Internet service: PC can connect to the internet. Download/upload testing with internal network (Using server belong to VNPT network) Trang bị bổ sung thiết bị cho các hệ thống IP DSLAM Huawei đợt I năm 2014 Page 9 of 21 Procedure of Test IP DSLAM Using www.speedtest.net for testing these rates. Choosing server belong to VNPT Group like the picture below (Hosted by VNPT) The test case pass if the rate achieve 80% of configured rate • Download/upload testing with external network: (Using server belong to other ISP in Vietnam) Using www.speedtest.net for testing these rates. Choosing server belong to FPT ISP like the picture below (Hosted by FPT-Telecom) The test case pass if the rate achieve 60% of configured rate Trang bị bổ sung thiết bị cho các hệ thống IP DSLAM Huawei đợt I năm 2014 Page 10 of 21 Procedure of Test IP DSLAM IPTV service: PC can connect to IPTV by VLC IPTV service can test pass by measure device Note: the bit rate can be achieved depends on the quality of cable. Test Result: Distances(Km) Example: VPN 512/512 1 Ratio (1) 2 Ratio (2) 3 Ratio (3) 512/512 100/100 484/484 94/94 460/460 89/89 DL/UL rate (kbps) - VPN packet 512/512 DL/UL rate (kbps) - HSI packet 4060/512 (internal network) DL/UL rate (kbps) - HSI packet 5120/640 (internal network) DL/UL rate (kbps) - HSI packet 4060/512 (external network) DL/UL rate (kbps) - HSI packet 5120/640 (external network) Passed [ ] Signature Failed [ ] Not tested [ ] Date/Time: Representative of VNPT: …………………………………………………………………………….. Trang bị bổ sung thiết bị cho các hệ thống IP DSLAM Huawei đợt I năm 2014 Page 11 of 21 Pass / Failed Pass Procedure of Test IP DSLAM T01-04 ADSL2+ Board Functions Test T01-0401 ADSL channel mode (Fast/Interleave) Objective To verify whether the proposed IP-DSLAM is able to support both fast and interleave ADSL channel mode. Network diagram FE GE ADSL User PC CPE DSLAM Server Prerequisites The cabling for the CPE is correct. Procedure 1. Add a configuration profile, set the channel mode to fast, and use this profile to deliver activation command to the port to be tested. View the line activation parameters after the port is activated. 2. Add a configuration profile, set the channel mode to interleave, and use this profile to deliver activation command to the port to be tested. View the line activation parameters after the port is activated. Expected result 1. In Step 1, the port can be activated; after the activation, the parameter shows that the current channel mode is Fast; and the activation rate conforms to the actual situation. 2. In Step 2, the port can be activated; after the activation, the parameter shows that the current channel mode is Interleave; and the activation rate conforms to the actual situation Remarks Test Result Passed [ ] Failed [ ] Not tested [ ] Date/Time: Signature Representative of VNPT: …………………………………………………………………………….. T01-0402 Noise threshold setting Objective To verify whether the proposed IP-DSLAM is able to support Noise Threshold Setting function. Network diagram FE GE User DSLAM Server D Prerequisites z z The CPE supports G.992.1, G.992.2, G.992.3, G.992.4, G.992.5, and T1.413. The cabling for the CPE is correct. Trang bị bổ sung thiết bị cho các hệ thống IP DSLAM Huawei đợt I năm 2014 Page 12 of 21 Procedure of Test IP DSLAM Procedure 1. Add multiple configuration profiles, and set different noise thresholds for different configuration profiles, and then use one type of profile to deliver activation command. 2. After the port is activated, check the line activation parameters. 3. Use another type of configuration profile to deliver activation command, and set the noise threshold to be higher than that in Step 1. Check the line activation parameters after the port is activated. 4. Use another type of configuration profile to deliver activation command, and set the noise threshold to be lower than that in Step 1. Check the line activation parameters after the port is activated Expected result 1. In Step 3, the activation rate should be lower than that in Step 2. 2. In Step 4, the activation rate should be higher than that in Step 2. Remarks Test Result Passed [ ] Failed [ ] Not tested [ ] Date/Time: Signature Representative of VNPT: …………………………………………………………………………….. T01-0403 ADSL2+ high-bit-rate and long-distance feature Objective To verify whether the proposed IP-DSLAM is able to support ADSL2+ high-bit-rate and long-distance feature. Network diagram Server Internet PC Prerequisites Procedure z z CPE MA5600 The MA5600 system runs normally. A CPE is connected to an ADSL2+ port, and the CPE works normally. 1. The DSLAM device and the ADSL2+ board function normally; 2. The ADSL2+ port is connected to the CPE; 3. The IDM or NetperSec tool is available. 4. The line-profile is shown as below: LINE-PROFILE-99 Line-Profile name atuc channel interleave max tx-rate(Kbps) 28800 1. Use the IDM or NetperSec tool to check speed with different line distances: 3 and 5 km, and add an ADSL line profile; Trang bị bổ sung thiết bị cho các hệ thống IP DSLAM Huawei đợt I năm 2014 Page 13 of 21 Procedure of Test IP DSLAM 2. Set the parameters of the line profile; 3. Display the line profile to view the configured line attributes; 4. Deliver the activation command; 5. Display the actual port rate after sync; 6. Repeat steps 1–6 using different CPE(s). Expected result Remarks Distances (km) 1 2 3 Rate (Mbps) 25 8 3 1 2 3 None Distances (km) Rate (Mbps) Test Result Passed [ ] Failed [ ] Not tested [ ] Date/Time: Signature Representative of VNPT: …………………………………………………………………………….. T01-05 N2000 Compatiblity test T01-0501 Querying the details of the ADSL port Objective To verify the function of querying the details of the ADSL port Network diagram None Prerequisites The N2000 BMS is in the normal state. Procedure z You have logged in to the N2000 BMS and have the rights to manage the device. 1. Choose Access Service > DSL > ADSL Port from the main menu. 2. On the interface that appears, select MA5600V3 from the Device Type dropdown list. Click Filter. In the dialog box that appears, set the filtering criteria to display the desired records. Select an ADSL port, and query the port information on the Basic Info. tab. Expected result Querying the details of the ADSL port succeeds. Remarks Test Result Passed [ ] Failed [ ] Not tested [ ] Date/Time: Signature Representative of VNPT: …………………………………………………………………………….. T01-0502 Configuring an ADSL2+ Line profile Trang bị bổ sung thiết bị cho các hệ thống IP DSLAM Huawei đợt I năm 2014 Page 14 of 21 Procedure of Test IP DSLAM Objective To verify the function of configuring an ADSL2+ line profile Network diagram None Prerequisites The N2000 BMS is in the normal state. Procedure z You have logged in to the N2000 BMS and have the rights to manage the device. 1. Choose Access Service > DSL > ADSL Port from the main menu. 2. On the interface that appears, select MA5600V3 from the Device Type dropdown list. Click Filter. In the dialog box that appears, set the filtering criteria to display the desired records. 3. Select an ADSL port, right-click, and choose Configure. 4. In the dialog box that appears, select the line profile check box. In the dialog box that appears, select the desired line profile, and click OK. In the dialog box that appears, click OK. Expected result Configuring the ADSL line profile succeeds. You can query the bound line profile on the Line Profile tab. Remarks Test Result Passed [ ] Failed [ ] Not tested [ ] Date/Time: Signature Representative of VNPT: ……………………………………………………………………………… T01-0503 ADSL2+ IPoE/PPPoE Access Service Objective To verify the function of the ADSL2+IPoE/PPPoE access service Network diagram Prerequisites The N2000 BMS is in the normal state. Trang bị bổ sung thiết bị cho các hệ thống IP DSLAM Huawei đợt I năm 2014 Page 15 of 21 Procedure of Test IP DSLAM z Procedure You have logged in to the N2000 BMS and have the rights to manage the device. 1. 2. Query and configure a traffic profile. 3. 4. Check whether the port is activated. 5. Bind ADSL2+ port 0/1/0 and the default alarm profile. 6. Use the default line profile 1002 to activate the port. Configure a VLAN. Check whether there is any proper ADSL2+ line profile (in both cases: PPPoE and IPoE mode) Save the data Expected result 1. Can access the Internet in the IPoE mode. 2. Can access the Internet in the PPPoE mode. Remarks Test Result Passed [ ] Failed [ ] Not tested [ ] Date/Time: Signature Representative of VNPT: …………………………………………………………………………….. Trang bị bổ sung thiết bị cho các hệ thống IP DSLAM Huawei đợt I năm 2014 Page 16 of 21 Procedure of Test IP DSLAM T01-0504 Triple Play Service Objective To verify the function of the triple play service Network diagram None Prerequisites The N2000 BMS is in the normal state. Procedure z 1. You have logged in to the N2000 BMS and have the rights to manage the device. Procedure for configuring the Triple play service in the multi-PVC Internet service mode: Create a VLAN. Add a subport. Configure a traffic profile. Add a service virtual port. 2. Configuring the Triple play service in the multi-PVC VoIP service mode: Create a VLAN. Add a subport, and configure an L3 interface. Configure a traffic profile. Add a service virtual port. Select the DHCP relay mode. Add a domain, and bind a DHCP server group for the domain. Configure the gateway IP address of the domain. 3. Configuring the Triple play service in the multi-PVC IPTV service mode: Configure VPI/VCI for ADSL2+ port for MyTV service. Mapping port-VPI/VCI. Connect CPE to STB. Expected result Providing services in 1 ADSL2+ port of the card under test at the same time: - Internet access - MyTV HD - VoIP IMS of VNPT Remarks Test Result Passed [ ] Failed [ ] Not tested [ ] Date/Time: Signature Representative of VNPT: …………………………………………………………………………….. Trang bị bổ sung thiết bị cho các hệ thống IP DSLAM Huawei đợt I năm 2014 Page 17 of 21